SUBRANG CLASSIC SYNTHETIC ENAMEL

Recommended for use on: Doors, windows, chipboard, hardboard, wood and metal surfaces. It can also be used on walls, concrete and masonry surfaces. Application is to be done after proper dilution (depending on the application- brush, roller or spray) with colorless oil paint thinner / white spirit.

Product Features:

· Mirror Like Gloss Finish

· Easy Application & Superior Leveling

· Hard Wearing, Tough & Durable

· Steam & Water Resistant*

· High Opacity & Long Lasting Performance*

· Scratch & Stain Resistant

Application Guide

Wood Work:

Sand down the surface with sand paper or emery paper and apply one coat of Subrang Classic Primer. Next, prepare the surface by applying 1-2 Coats of Subrang Classic Wall Putty (if required). After filling is dry sand paper the surface and apply 2 coats of Subrang Classic Synthetic Enamel (after preparing the material / diluting as per the application method). In case the oil is coming out from the wood, remove oil by scraping and seal the oily portion by shellac solution prior to final painting.

Coating System: 1 Coat (Primer) + 1-2 Coats (Putty if required) +1 Coat (Primer if filling putty is applied) + 2 Coats (Synthetic Enamel)

Steel Structure

Remove all dust, dirt and loose adhering or flaked paints by scarping with scraper, emery paper or sand blasting. Remove all the rust by sanding, rust removing solution or by flame, and then apply one coat of Subrang Classic Red Oxide Primer followed by 2 coats of Subrang Classic Synthetic Enamel.

Coating System: 1 Coat (Primer) +2 Coats (Synthetic Enamel)

Technical Information:

Theoretical Coverage: 15-17 m² per liter per coat (Actual Coverage is dependent on

substrate condition, application method, application condition, finishing

appearance and wastage during painting etc.)

Color: As per shade card

Volume Solid: 46 % ± 2

Dry Film Thickness: 28 ± 3 um per coat (based on substrate condition)

Finish: High Gloss

Flash Point: 36⁰C ± 2

Drying Time: Touch Dry 4 - 6 hours (Dependent on temperature and humidity)

Hard dry 24 hours (Dependent on temperature and humidity)

Recoat Interval: 14 - 16 hours (Dependent on temperature and humidity)

Application Method: Brush / Roller and spray, dilute (by volume) the paint 10 – 15 %. (This is recommended method of application Care should be taken to ensure an even application to avoid film defects)

Packing: 0.91 Liter, 3.64 Liters & 14.56 Liters drum

Safety & Precautions

• Make sure there is ample ventilation available before, during and after painting.

• Keep children and pets away from painted areas and appliances.

• When applying paint, it is preferable to wear eye safety goggles and dust mask.

• Never leave opened container unattended.

• To clean paint from your hands, use soap and water only.

Storage & Handling

• Keep away from heat and spark sources, away from direct sunlight.

• Never breathe in dust, mist, gas or vapors from the dry product.

• Keep the containers closed in storage.

• Do not apply during rain/fog/mist/wind or when the temperature is below 5 °C.

• In case of eye contact: Wash with plenty of cold water and immediately consult a physician.

• In case of ingestion: drink plenty of water or milk, do not induce vomiting, & consult a doctor.

• In case of inhalation: remove the person to open fresh air area, provide artificial breathing if needed, and consult a doctor.

Disclaimer:

The information provided on this data sheet is not intended to be completed and is provided as general advice only. It is the responsibility of the user to ensure that the product is suitable for the purpose for which he wishes to use it. As we have no control over the treatment of the product, the standard of surface preparation of the substrate, or other factors affecting the use of this product, we are not responsible for its performance nor would we accept any liability whatsoever or howsoever arising from the use of this product unless specifically agreed to in writing by us. The information contained in this data sheet may be modified by us from time to time, and without notice, in the light of our experience and continuous product development.